Bryan beside a green 1976 GMC with a grille-inspired magnetic hook design and JBL Clip 5 speaker

A 3D-Printed Magnetic JBL Clip 5 Holder for My 1976 GMC

My 1976 GMC Sierra Classic needs better sound, but I want to keep the truck as original as possible. Rather than change the dashboard, I decided to use a JBL Clip 5 Bluetooth speaker—and design a removable holder that looks like it belongs in the truck.

The result combines a grille-inspired ABS body, a flexible TPU backing, and six magnets. There are no holes drilled into the truck and no permanent changes to the dashboard for this project.

This post contains affiliate links, which may earn us a commission. As an Amazon Associate I earn from qualifying purchases.

A speaker holder inspired by the GMC grille

I wanted something more interesting than a plain magnetic hook. Taking inspiration from the front grille of the 1976 GMC, I designed a small grille with hooks for the JBL Clip 5.

The back has six recessed pockets for neodymium magnets. That lets the assembly attach to a suitable metal surface while remaining removable. The design went through a few prototypes before reaching the version shown in the video.

Why I used ABS for the main body

I printed the rigid grille in gray Anycubic ABS. My reason for choosing it over standard PLA was heat: a truck sitting in summer sun can become a demanding environment for a printed accessory.

The rigid body provides the shape and hooks, while a separate backing handles the contact with the truck.

TPU between the magnets and the paint

I did not want the magnets touching the truck's paint directly. Movement and vibration could otherwise turn a useful holder into a source of scratches.

For the backing, I used black Siraya Tech TPU Air 95A. The flexible layer is intended to cushion the contact surface and add friction against the painted metal.

The backing is approximately 3 mm thick overall, with recesses near the magnets that leave about 1 mm of TPU between the magnets and the truck. That difference matters because increasing the gap between a magnet and the steel reduces the attraction.

Holding against sliding is different from pulling straight off

The build uses six N52 neodymium magnets, each 12 mm in diameter and 3 mm thick. Their advertised pull force is not automatically the load the assembled holder can resist while hanging on a painted surface.

For this project, the speaker's tendency to slide downward is a key concern. The useful relationship discussed in the video is:

Available friction force = coefficient of friction × magnetic clamping force.

Using a hypothetical 1-pound combined load, a factor of three, and a friction coefficient of 0.5, the example calculation gives:

  • 1 pound × 3 = 3 pounds of downward force to resist.
  • 3 ÷ 0.5 = 6 pounds of total effective clamping force.
  • Across six magnets, that averages 1 pound of effective clamping force per magnet.

Those are assumptions for an illustrative calculation, not measured friction or clamping-force values for the finished mount. The TPU gap, paint, steel thickness, and actual contact can change the result. The calculation provides a starting point for testing.

Printing, assembly, and the first fit test

After printing the ABS grille and TPU backing, I installed the six magnets in their recessed pockets, made sure they were retained, and attached the backing.

For the hands-on check, I attached the grille to the truck and hung the JBL Clip 5 from it. I checked whether it slid under its own weight, gently pulled downward, and checked how easily the mount could peel away from the metal.

The assembly stayed in place during the fit and slide checks shown. That was encouraging, but the video also notes that bumps and vibration still need testing before trusting the mount on the road. A successful stationary fit test is only the first step.

Watch the magnetic speaker mount project

Design files from the video

Materials linked in the video

This is the kind of problem I enjoy solving with 3D printing: make the accessory fit the truck, while keeping the original truck intact. Would you keep the original radio and use a removable speaker, or install a modern stereo?

Back to blog